ConfiguratorA

Package: inet.tutorials.configurator

ConfiguratorA

network

(no description)

Ipv4NetworkConfigurator StandardHost StandardHost StandardHost StandardHost Router Router Router StandardHost StandardHost StandardHost StandardHost StandardHost EthernetSwitch EthernetSwitch EthernetSwitch IntegratedCanvasVisualizer

Usage diagram

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Properties

Name Value Description
isNetwork
display bgb=1610.5125,874.96497

Unassigned submodule parameters

Name Type Default value Description
configurator.minLinkWeight double 1E-3
configurator.configureIsolatedNetworksSeparatly bool false
configurator.config xml xml("")

XML configuration parameters for IP address assignment and adding manual routes
configurator.assignAddresses bool true

assign IP addresses to all interfaces in the network
configurator.assignUniqueAddresses bool true

avoid using the same address and raise an error if not possible
configurator.assignDisjunctSubnetAddresses bool true

avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces
configurator.addStaticRoutes bool true

add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator.addDefaultRoutes bool true

add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator.addSubnetRoutes bool true

add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator.addDirectRoutes bool true

add direct routes (i.e. directly connected interfaces) to the routing table (used only if addStaticRoutes is true)
configurator.optimizeRoutes bool true

optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator.dumpTopology bool false

print extracted network topology to the module output
configurator.dumpLinks bool false

print recognized network links to the module output
configurator.dumpAddresses bool false

print assigned IP addresses for all interfaces to the module output
configurator.dumpRoutes bool false

print configured and optimized routing tables for all nodes to the module output
configurator.dumpConfig string ""

write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)
host0.status.initialStatus string "UP"

TODO @signal, @statistic
host0.pcapRecorder.verbose bool true

whether to log packets on the module output
host0.pcapRecorder.pcapFile string ""

the PCAP file to be written
host0.pcapRecorder.fileFormat string "pcapng"
host0.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host0.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host0.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
host0.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host0.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host0.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
host0.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
host0.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
host0.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host0.pcapRecorder.displayStringTextFormat string "rec: %n pks"
host0.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host0.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host0.cb.forwardServiceRegistration bool true
host0.cb.forwardProtocolRegistration bool true
host0.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host0.bl.forwardServiceRegistration bool true
host0.bl.forwardProtocolRegistration bool true
host0.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host0.li.forwardServiceRegistration bool true
host0.li.forwardProtocolRegistration bool true
host0.eth.bitrate double
host0.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host0.nl.forwardServiceRegistration bool true
host0.nl.forwardProtocolRegistration bool true
host0.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host0.tn.forwardServiceRegistration bool true
host0.tn.forwardProtocolRegistration bool true
host0.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host0.at.forwardServiceRegistration bool true
host0.at.forwardProtocolRegistration bool true
host1.status.initialStatus string "UP"

TODO @signal, @statistic
host1.pcapRecorder.verbose bool true

whether to log packets on the module output
host1.pcapRecorder.pcapFile string ""

the PCAP file to be written
host1.pcapRecorder.fileFormat string "pcapng"
host1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
host1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host1.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
host1.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
host1.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
host1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host1.pcapRecorder.displayStringTextFormat string "rec: %n pks"
host1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host1.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host1.cb.forwardServiceRegistration bool true
host1.cb.forwardProtocolRegistration bool true
host1.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host1.bl.forwardServiceRegistration bool true
host1.bl.forwardProtocolRegistration bool true
host1.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host1.li.forwardServiceRegistration bool true
host1.li.forwardProtocolRegistration bool true
host1.eth.bitrate double
host1.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host1.nl.forwardServiceRegistration bool true
host1.nl.forwardProtocolRegistration bool true
host1.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host1.tn.forwardServiceRegistration bool true
host1.tn.forwardProtocolRegistration bool true
host1.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host1.at.forwardServiceRegistration bool true
host1.at.forwardProtocolRegistration bool true
host2.status.initialStatus string "UP"

TODO @signal, @statistic
host2.pcapRecorder.verbose bool true

whether to log packets on the module output
host2.pcapRecorder.pcapFile string ""

the PCAP file to be written
host2.pcapRecorder.fileFormat string "pcapng"
host2.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host2.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host2.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
host2.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host2.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host2.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
host2.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
host2.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
host2.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host2.pcapRecorder.displayStringTextFormat string "rec: %n pks"
host2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host2.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host2.cb.forwardServiceRegistration bool true
host2.cb.forwardProtocolRegistration bool true
host2.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host2.bl.forwardServiceRegistration bool true
host2.bl.forwardProtocolRegistration bool true
host2.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host2.li.forwardServiceRegistration bool true
host2.li.forwardProtocolRegistration bool true
host2.eth.bitrate double
host2.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host2.nl.forwardServiceRegistration bool true
host2.nl.forwardProtocolRegistration bool true
host2.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host2.tn.forwardServiceRegistration bool true
host2.tn.forwardProtocolRegistration bool true
host2.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host2.at.forwardServiceRegistration bool true
host2.at.forwardProtocolRegistration bool true
host3.status.initialStatus string "UP"

TODO @signal, @statistic
host3.pcapRecorder.verbose bool true

whether to log packets on the module output
host3.pcapRecorder.pcapFile string ""

the PCAP file to be written
host3.pcapRecorder.fileFormat string "pcapng"
host3.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host3.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host3.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
host3.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host3.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host3.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
host3.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
host3.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
host3.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host3.pcapRecorder.displayStringTextFormat string "rec: %n pks"
host3.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host3.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host3.cb.forwardServiceRegistration bool true
host3.cb.forwardProtocolRegistration bool true
host3.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host3.bl.forwardServiceRegistration bool true
host3.bl.forwardProtocolRegistration bool true
host3.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host3.li.forwardServiceRegistration bool true
host3.li.forwardProtocolRegistration bool true
host3.eth.bitrate double
host3.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host3.nl.forwardServiceRegistration bool true
host3.nl.forwardProtocolRegistration bool true
host3.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host3.tn.forwardServiceRegistration bool true
host3.tn.forwardProtocolRegistration bool true
host3.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host3.at.forwardServiceRegistration bool true
host3.at.forwardProtocolRegistration bool true
router0.status.initialStatus string "UP"

TODO @signal, @statistic
router0.pcapRecorder.verbose bool true

whether to log packets on the module output
router0.pcapRecorder.pcapFile string ""

the PCAP file to be written
router0.pcapRecorder.fileFormat string "pcapng"
router0.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
router0.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
router0.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
router0.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
router0.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
router0.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
router0.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
router0.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
router0.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
router0.pcapRecorder.displayStringTextFormat string "rec: %n pks"
router0.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
router0.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router0.cb.forwardServiceRegistration bool true
router0.cb.forwardProtocolRegistration bool true
router0.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router0.bl.forwardServiceRegistration bool true
router0.bl.forwardProtocolRegistration bool true
router0.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router0.li.forwardServiceRegistration bool true
router0.li.forwardProtocolRegistration bool true
router0.eth.bitrate double
router0.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router0.nl.forwardServiceRegistration bool true
router0.nl.forwardProtocolRegistration bool true
router0.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router0.tn.forwardServiceRegistration bool true
router0.tn.forwardProtocolRegistration bool true
router0.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router0.at.forwardServiceRegistration bool true
router0.at.forwardProtocolRegistration bool true
router0.bgp.interfaceTableModule string

The path to the InterfaceTable module
router0.bgp.routingTableModule string
router0.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
router2.status.initialStatus string "UP"

TODO @signal, @statistic
router2.pcapRecorder.verbose bool true

whether to log packets on the module output
router2.pcapRecorder.pcapFile string ""

the PCAP file to be written
router2.pcapRecorder.fileFormat string "pcapng"
router2.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
router2.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
router2.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
router2.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
router2.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
router2.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
router2.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
router2.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
router2.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
router2.pcapRecorder.displayStringTextFormat string "rec: %n pks"
router2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
router2.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router2.cb.forwardServiceRegistration bool true
router2.cb.forwardProtocolRegistration bool true
router2.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router2.bl.forwardServiceRegistration bool true
router2.bl.forwardProtocolRegistration bool true
router2.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router2.li.forwardServiceRegistration bool true
router2.li.forwardProtocolRegistration bool true
router2.eth.bitrate double
router2.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router2.nl.forwardServiceRegistration bool true
router2.nl.forwardProtocolRegistration bool true
router2.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router2.tn.forwardServiceRegistration bool true
router2.tn.forwardProtocolRegistration bool true
router2.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router2.at.forwardServiceRegistration bool true
router2.at.forwardProtocolRegistration bool true
router2.bgp.interfaceTableModule string

The path to the InterfaceTable module
router2.bgp.routingTableModule string
router2.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
router1.status.initialStatus string "UP"

TODO @signal, @statistic
router1.pcapRecorder.verbose bool true

whether to log packets on the module output
router1.pcapRecorder.pcapFile string ""

the PCAP file to be written
router1.pcapRecorder.fileFormat string "pcapng"
router1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
router1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
router1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
router1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
router1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
router1.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
router1.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
router1.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
router1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
router1.pcapRecorder.displayStringTextFormat string "rec: %n pks"
router1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
router1.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router1.cb.forwardServiceRegistration bool true
router1.cb.forwardProtocolRegistration bool true
router1.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router1.bl.forwardServiceRegistration bool true
router1.bl.forwardProtocolRegistration bool true
router1.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router1.li.forwardServiceRegistration bool true
router1.li.forwardProtocolRegistration bool true
router1.eth.bitrate double
router1.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router1.nl.forwardServiceRegistration bool true
router1.nl.forwardProtocolRegistration bool true
router1.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router1.tn.forwardServiceRegistration bool true
router1.tn.forwardProtocolRegistration bool true
router1.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router1.at.forwardServiceRegistration bool true
router1.at.forwardProtocolRegistration bool true
router1.bgp.interfaceTableModule string

The path to the InterfaceTable module
router1.bgp.routingTableModule string
router1.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
host4.status.initialStatus string "UP"

TODO @signal, @statistic
host4.pcapRecorder.verbose bool true

whether to log packets on the module output
host4.pcapRecorder.pcapFile string ""

the PCAP file to be written
host4.pcapRecorder.fileFormat string "pcapng"
host4.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host4.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host4.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
host4.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host4.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host4.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
host4.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
host4.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
host4.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host4.pcapRecorder.displayStringTextFormat string "rec: %n pks"
host4.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host4.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host4.cb.forwardServiceRegistration bool true
host4.cb.forwardProtocolRegistration bool true
host4.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host4.bl.forwardServiceRegistration bool true
host4.bl.forwardProtocolRegistration bool true
host4.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host4.li.forwardServiceRegistration bool true
host4.li.forwardProtocolRegistration bool true
host4.eth.bitrate double
host4.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host4.nl.forwardServiceRegistration bool true
host4.nl.forwardProtocolRegistration bool true
host4.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host4.tn.forwardServiceRegistration bool true
host4.tn.forwardProtocolRegistration bool true
host4.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host4.at.forwardServiceRegistration bool true
host4.at.forwardProtocolRegistration bool true
host5.status.initialStatus string "UP"

TODO @signal, @statistic
host5.pcapRecorder.verbose bool true

whether to log packets on the module output
host5.pcapRecorder.pcapFile string ""

the PCAP file to be written
host5.pcapRecorder.fileFormat string "pcapng"
host5.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host5.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host5.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
host5.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host5.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host5.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
host5.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
host5.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
host5.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host5.pcapRecorder.displayStringTextFormat string "rec: %n pks"
host5.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host5.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host5.cb.forwardServiceRegistration bool true
host5.cb.forwardProtocolRegistration bool true
host5.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host5.bl.forwardServiceRegistration bool true
host5.bl.forwardProtocolRegistration bool true
host5.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host5.li.forwardServiceRegistration bool true
host5.li.forwardProtocolRegistration bool true
host5.eth.bitrate double
host5.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host5.nl.forwardServiceRegistration bool true
host5.nl.forwardProtocolRegistration bool true
host5.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host5.tn.forwardServiceRegistration bool true
host5.tn.forwardProtocolRegistration bool true
host5.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host5.at.forwardServiceRegistration bool true
host5.at.forwardProtocolRegistration bool true
host6.status.initialStatus string "UP"

TODO @signal, @statistic
host6.pcapRecorder.verbose bool true

whether to log packets on the module output
host6.pcapRecorder.pcapFile string ""

the PCAP file to be written
host6.pcapRecorder.fileFormat string "pcapng"
host6.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host6.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host6.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
host6.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host6.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host6.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
host6.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
host6.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
host6.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host6.pcapRecorder.displayStringTextFormat string "rec: %n pks"
host6.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host6.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host6.cb.forwardServiceRegistration bool true
host6.cb.forwardProtocolRegistration bool true
host6.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host6.bl.forwardServiceRegistration bool true
host6.bl.forwardProtocolRegistration bool true
host6.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host6.li.forwardServiceRegistration bool true
host6.li.forwardProtocolRegistration bool true
host6.eth.bitrate double
host6.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host6.nl.forwardServiceRegistration bool true
host6.nl.forwardProtocolRegistration bool true
host6.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host6.tn.forwardServiceRegistration bool true
host6.tn.forwardProtocolRegistration bool true
host6.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host6.at.forwardServiceRegistration bool true
host6.at.forwardProtocolRegistration bool true
host7.status.initialStatus string "UP"

TODO @signal, @statistic
host7.pcapRecorder.verbose bool true

whether to log packets on the module output
host7.pcapRecorder.pcapFile string ""

the PCAP file to be written
host7.pcapRecorder.fileFormat string "pcapng"
host7.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host7.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host7.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
host7.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host7.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host7.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
host7.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
host7.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
host7.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host7.pcapRecorder.displayStringTextFormat string "rec: %n pks"
host7.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host7.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host7.cb.forwardServiceRegistration bool true
host7.cb.forwardProtocolRegistration bool true
host7.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host7.bl.forwardServiceRegistration bool true
host7.bl.forwardProtocolRegistration bool true
host7.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host7.li.forwardServiceRegistration bool true
host7.li.forwardProtocolRegistration bool true
host7.eth.bitrate double
host7.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host7.nl.forwardServiceRegistration bool true
host7.nl.forwardProtocolRegistration bool true
host7.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host7.tn.forwardServiceRegistration bool true
host7.tn.forwardProtocolRegistration bool true
host7.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host7.at.forwardServiceRegistration bool true
host7.at.forwardProtocolRegistration bool true
host8.status.initialStatus string "UP"

TODO @signal, @statistic
host8.pcapRecorder.verbose bool true

whether to log packets on the module output
host8.pcapRecorder.pcapFile string ""

the PCAP file to be written
host8.pcapRecorder.fileFormat string "pcapng"
host8.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host8.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host8.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
host8.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host8.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host8.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
host8.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
host8.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
host8.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host8.pcapRecorder.displayStringTextFormat string "rec: %n pks"
host8.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host8.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host8.cb.forwardServiceRegistration bool true
host8.cb.forwardProtocolRegistration bool true
host8.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host8.bl.forwardServiceRegistration bool true
host8.bl.forwardProtocolRegistration bool true
host8.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host8.li.forwardServiceRegistration bool true
host8.li.forwardProtocolRegistration bool true
host8.eth.bitrate double
host8.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host8.nl.forwardServiceRegistration bool true
host8.nl.forwardProtocolRegistration bool true
host8.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host8.tn.forwardServiceRegistration bool true
host8.tn.forwardProtocolRegistration bool true
host8.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
host8.at.forwardServiceRegistration bool true
host8.at.forwardProtocolRegistration bool true
switch0.macTable.agingTime double
switch0.macTable.forwardingTableFile string
switch0.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
switch0.l2NodeConfigurator.interfaceTableModule string
switch0.l2NodeConfigurator.l2ConfiguratorModule string "l2NetworkConfigurator"

the absolute path to the ~L2NetworkConfigurator; use "" if there is no configurator
switch0.status.initialStatus string "UP"

TODO @signal, @statistic
switch0.pcapRecorder.verbose bool true

whether to log packets on the module output
switch0.pcapRecorder.pcapFile string ""

the PCAP file to be written
switch0.pcapRecorder.fileFormat string "pcapng"
switch0.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
switch0.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
switch0.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
switch0.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
switch0.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
switch0.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
switch0.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
switch0.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
switch0.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
switch0.pcapRecorder.displayStringTextFormat string "rec: %n pks"
switch0.stp.helloTime double
switch0.stp.forwardDelay double
switch0.stp.maxAge double
switch0.stp.bridgePriority int
switch0.stp.visualize bool
switch0.sc.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch0.sc.forwardServiceRegistration bool true
switch0.sc.forwardProtocolRegistration bool true
switch0.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch0.cb.forwardServiceRegistration bool true
switch0.cb.forwardProtocolRegistration bool true
switch0.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch0.bl.forwardServiceRegistration bool true
switch0.bl.forwardProtocolRegistration bool true
switch0.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch0.li.forwardServiceRegistration bool true
switch0.li.forwardProtocolRegistration bool true
switch0.cutthrough.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch0.cutthrough.forwardServiceRegistration bool true
switch0.cutthrough.forwardProtocolRegistration bool true
switch0.eth.bitrate double
switch2.macTable.agingTime double
switch2.macTable.forwardingTableFile string
switch2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
switch2.l2NodeConfigurator.interfaceTableModule string
switch2.l2NodeConfigurator.l2ConfiguratorModule string "l2NetworkConfigurator"

the absolute path to the ~L2NetworkConfigurator; use "" if there is no configurator
switch2.status.initialStatus string "UP"

TODO @signal, @statistic
switch2.pcapRecorder.verbose bool true

whether to log packets on the module output
switch2.pcapRecorder.pcapFile string ""

the PCAP file to be written
switch2.pcapRecorder.fileFormat string "pcapng"
switch2.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
switch2.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
switch2.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
switch2.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
switch2.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
switch2.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
switch2.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
switch2.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
switch2.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
switch2.pcapRecorder.displayStringTextFormat string "rec: %n pks"
switch2.stp.helloTime double
switch2.stp.forwardDelay double
switch2.stp.maxAge double
switch2.stp.bridgePriority int
switch2.stp.visualize bool
switch2.sc.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch2.sc.forwardServiceRegistration bool true
switch2.sc.forwardProtocolRegistration bool true
switch2.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch2.cb.forwardServiceRegistration bool true
switch2.cb.forwardProtocolRegistration bool true
switch2.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch2.bl.forwardServiceRegistration bool true
switch2.bl.forwardProtocolRegistration bool true
switch2.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch2.li.forwardServiceRegistration bool true
switch2.li.forwardProtocolRegistration bool true
switch2.cutthrough.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch2.cutthrough.forwardServiceRegistration bool true
switch2.cutthrough.forwardProtocolRegistration bool true
switch2.eth.bitrate double
switch1.macTable.agingTime double
switch1.macTable.forwardingTableFile string
switch1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
switch1.l2NodeConfigurator.interfaceTableModule string
switch1.l2NodeConfigurator.l2ConfiguratorModule string "l2NetworkConfigurator"

the absolute path to the ~L2NetworkConfigurator; use "" if there is no configurator
switch1.status.initialStatus string "UP"

TODO @signal, @statistic
switch1.pcapRecorder.verbose bool true

whether to log packets on the module output
switch1.pcapRecorder.pcapFile string ""

the PCAP file to be written
switch1.pcapRecorder.fileFormat string "pcapng"
switch1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
switch1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
switch1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
switch1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
switch1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
switch1.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
switch1.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
switch1.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
switch1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
switch1.pcapRecorder.displayStringTextFormat string "rec: %n pks"
switch1.stp.helloTime double
switch1.stp.forwardDelay double
switch1.stp.maxAge double
switch1.stp.bridgePriority int
switch1.stp.visualize bool
switch1.sc.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch1.sc.forwardServiceRegistration bool true
switch1.sc.forwardProtocolRegistration bool true
switch1.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch1.cb.forwardServiceRegistration bool true
switch1.cb.forwardProtocolRegistration bool true
switch1.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch1.bl.forwardServiceRegistration bool true
switch1.bl.forwardProtocolRegistration bool true
switch1.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch1.li.forwardServiceRegistration bool true
switch1.li.forwardProtocolRegistration bool true
switch1.cutthrough.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch1.cutthrough.forwardServiceRegistration bool true
switch1.cutthrough.forwardProtocolRegistration bool true
switch1.eth.bitrate double

Source code

network ConfiguratorA
{
    @display("bgb=1610.5125,874.96497");
    submodules:
        configurator: Ipv4NetworkConfigurator {
            @display("p=100,100");
        }
        host0: StandardHost {
            @display("p=268.32748,417.6225");
        }
        host1: StandardHost {
            @display("p=227.9775,542.7075");
        }
        host2: StandardHost {
            @display("p=268.32748,736.3875");
        }
        host3: StandardHost {
            @display("p=667.7925,98.8575");
        }
        router0: Router {
            @display("p=667.7925,574.9875");
        }
        router2: Router {
            @display("p=972.435,574.9875");
        }
        router1: Router {
            @display("p=821.1225,369.20248");
        }
        host4: StandardHost {
            @display("p=843.315,70.612495");
        }
        host5: StandardHost {
            @display("p=972.435,98.8575");
        }
        host6: StandardHost {
            @display("p=1430.4075,417.6225");
        }
        host7: StandardHost {
            @display("p=1472.775,542.7075");
        }
        host8: StandardHost {
            @display("p=1430.4075,736.3875");
        }
        switch0: EthernetSwitch {
            @display("p=518.4975,574.9875");
        }
        switch2: EthernetSwitch {
            @display("p=1162.08,574.9875");
        }
        switch1: EthernetSwitch {
            @display("p=821.1225,225.95999");
        }
        visualizer: IntegratedCanvasVisualizer {
            @display("p=98.8575,209.81999");
        }
    connections:
        host2.ethg++ <--> Eth100M <--> switch0.ethg++;
        host1.ethg++ <--> Eth100M <--> switch0.ethg++;
        host0.ethg++ <--> Eth100M <--> switch0.ethg++;
        switch0.ethg++ <--> Eth100M <--> router0.ethg++;
        router0.ethg++ <--> Eth100M <--> router1.ethg++;
        router1.ethg++ <--> Eth100M <--> switch1.ethg++;
        switch1.ethg++ <--> Eth100M <--> host3.ethg++;
        switch1.ethg++ <--> Eth100M <--> host4.ethg++;
        switch1.ethg++ <--> Eth100M <--> host5.ethg++;
        router1.ethg++ <--> Eth100M <--> router2.ethg++;
        router2.ethg++ <--> Eth100M <--> switch2.ethg++;
        switch2.ethg++ <--> Eth100M <--> host6.ethg++;
        switch2.ethg++ <--> Eth100M <--> host7.ethg++;
        switch2.ethg++ <--> Eth100M <--> host8.ethg++;
        router0.ethg++ <--> Eth10M <--> router2.ethg++;
}
File: tutorials/configurator/ConfiguratorA.ned

This documentation is released under the Creative Commons license