WiredAndWirelessHostsWithAP

Package: inet.examples.wireless.wiredandwirelesshostswithap

WiredAndWirelessHostsWithAP

network

(no description)

IIntegratedVisualizer Ipv4NetworkConfigurator Ieee80211ScalarRadioMedium WirelessHost StandardHost StandardHost Router AccessPoint

Usage diagram

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Properties

Name Value Description
isNetwork

Unassigned submodule parameters

Name Type Default value Description
configurator.minLinkWeight double 1E-3
configurator.configureIsolatedNetworksSeparatly bool false
configurator.config xml xml("")

XML configuration parameters for IP address assignment and adding manual routes
configurator.assignAddresses bool true

assign IP addresses to all interfaces in the network
configurator.assignUniqueAddresses bool true

avoid using the same address and raise an error if not possible
configurator.addStaticRoutes bool true

add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator.addDefaultRoutes bool true

add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator.addSubnetRoutes bool true

add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator.addDirectRoutes bool true

add direct routes (i.e. directly connected interfaces) to the routing table (used only if addStaticRoutes is true)
configurator.optimizeRoutes bool true

optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator.dumpTopology bool false

print extracted network topology to the module output
configurator.dumpLinks bool false

print recognized network links to the module output
configurator.dumpAddresses bool false

print assigned IP addresses for all interfaces to the module output
configurator.dumpRoutes bool false

print configured and optimized routing tables for all nodes to the module output
configurator.dumpConfig string ""

write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)
radioMedium.neighborCache.refillPeriod double
wirelessHost1.status.initialStatus string "UP"

TODO @signal, @statistic
wirelessHost1.pcapRecorder.verbose bool true

whether to log packets on the module output
wirelessHost1.pcapRecorder.pcapFile string ""

the PCAP file to be written
wirelessHost1.pcapRecorder.fileFormat string "pcapng"
wirelessHost1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
wirelessHost1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
wirelessHost1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
wirelessHost1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
wirelessHost1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
wirelessHost1.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
wirelessHost1.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
wirelessHost1.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
wirelessHost1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
wirelessHost1.pcapRecorder.displayStringTextFormat string "rec: %n pks"
wirelessHost1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
wirelessHost1.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wirelessHost1.cb.forwardServiceRegistration bool true
wirelessHost1.cb.forwardProtocolRegistration bool true
wirelessHost1.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wirelessHost1.bl.forwardServiceRegistration bool true
wirelessHost1.bl.forwardProtocolRegistration bool true
wirelessHost1.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wirelessHost1.li.forwardServiceRegistration bool true
wirelessHost1.li.forwardProtocolRegistration bool true
wirelessHost1.eth.bitrate double
wirelessHost1.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wirelessHost1.nl.forwardServiceRegistration bool true
wirelessHost1.nl.forwardProtocolRegistration bool true
wirelessHost1.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wirelessHost1.tn.forwardServiceRegistration bool true
wirelessHost1.tn.forwardProtocolRegistration bool true
wirelessHost1.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wirelessHost1.at.forwardServiceRegistration bool true
wirelessHost1.at.forwardProtocolRegistration bool true
wiredHost1.status.initialStatus string "UP"

TODO @signal, @statistic
wiredHost1.pcapRecorder.verbose bool true

whether to log packets on the module output
wiredHost1.pcapRecorder.pcapFile string ""

the PCAP file to be written
wiredHost1.pcapRecorder.fileFormat string "pcapng"
wiredHost1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
wiredHost1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
wiredHost1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
wiredHost1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
wiredHost1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
wiredHost1.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
wiredHost1.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
wiredHost1.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
wiredHost1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
wiredHost1.pcapRecorder.displayStringTextFormat string "rec: %n pks"
wiredHost1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
wiredHost1.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost1.cb.forwardServiceRegistration bool true
wiredHost1.cb.forwardProtocolRegistration bool true
wiredHost1.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost1.bl.forwardServiceRegistration bool true
wiredHost1.bl.forwardProtocolRegistration bool true
wiredHost1.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost1.li.forwardServiceRegistration bool true
wiredHost1.li.forwardProtocolRegistration bool true
wiredHost1.eth.bitrate double
wiredHost1.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost1.nl.forwardServiceRegistration bool true
wiredHost1.nl.forwardProtocolRegistration bool true
wiredHost1.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost1.tn.forwardServiceRegistration bool true
wiredHost1.tn.forwardProtocolRegistration bool true
wiredHost1.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost1.at.forwardServiceRegistration bool true
wiredHost1.at.forwardProtocolRegistration bool true
wiredHost2.status.initialStatus string "UP"

TODO @signal, @statistic
wiredHost2.pcapRecorder.verbose bool true

whether to log packets on the module output
wiredHost2.pcapRecorder.pcapFile string ""

the PCAP file to be written
wiredHost2.pcapRecorder.fileFormat string "pcapng"
wiredHost2.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
wiredHost2.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
wiredHost2.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
wiredHost2.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
wiredHost2.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
wiredHost2.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
wiredHost2.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
wiredHost2.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
wiredHost2.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
wiredHost2.pcapRecorder.displayStringTextFormat string "rec: %n pks"
wiredHost2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
wiredHost2.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost2.cb.forwardServiceRegistration bool true
wiredHost2.cb.forwardProtocolRegistration bool true
wiredHost2.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost2.bl.forwardServiceRegistration bool true
wiredHost2.bl.forwardProtocolRegistration bool true
wiredHost2.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost2.li.forwardServiceRegistration bool true
wiredHost2.li.forwardProtocolRegistration bool true
wiredHost2.eth.bitrate double
wiredHost2.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost2.nl.forwardServiceRegistration bool true
wiredHost2.nl.forwardProtocolRegistration bool true
wiredHost2.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost2.tn.forwardServiceRegistration bool true
wiredHost2.tn.forwardProtocolRegistration bool true
wiredHost2.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
wiredHost2.at.forwardServiceRegistration bool true
wiredHost2.at.forwardProtocolRegistration bool true
router.status.initialStatus string "UP"

TODO @signal, @statistic
router.pcapRecorder.verbose bool true

whether to log packets on the module output
router.pcapRecorder.pcapFile string ""

the PCAP file to be written
router.pcapRecorder.fileFormat string "pcapng"
router.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
router.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
router.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
router.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
router.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
router.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
router.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
router.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
router.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
router.pcapRecorder.displayStringTextFormat string "rec: %n pks"
router.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
router.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router.cb.forwardServiceRegistration bool true
router.cb.forwardProtocolRegistration bool true
router.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router.bl.forwardServiceRegistration bool true
router.bl.forwardProtocolRegistration bool true
router.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router.li.forwardServiceRegistration bool true
router.li.forwardProtocolRegistration bool true
router.eth.bitrate double
router.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router.nl.forwardServiceRegistration bool true
router.nl.forwardProtocolRegistration bool true
router.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router.tn.forwardServiceRegistration bool true
router.tn.forwardProtocolRegistration bool true
router.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
router.at.forwardServiceRegistration bool true
router.at.forwardProtocolRegistration bool true
router.bgp.interfaceTableModule string

The path to the InterfaceTable module
router.bgp.routingTableModule string
router.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
accessPoint.status.initialStatus string "UP"

TODO @signal, @statistic
accessPoint.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
accessPoint.macTable.agingTime double
accessPoint.macTable.forwardingTableFile string
accessPoint.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
accessPoint.bl.forwardServiceRegistration bool true
accessPoint.bl.forwardProtocolRegistration bool true
accessPoint.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
accessPoint.li.forwardServiceRegistration bool true
accessPoint.li.forwardProtocolRegistration bool true
accessPoint.eth.bitrate double

Source code

network WiredAndWirelessHostsWithAP
{
    submodules:
        visualizer: <default(firstAvailableOrEmpty("IntegratedCanvasVisualizer"))> like IIntegratedVisualizer if typename != "" {
            parameters:
                @display("p=100,300;is=s");
        }
        configurator: Ipv4NetworkConfigurator {
            parameters:
                assignDisjunctSubnetAddresses = false;
                @display("p=100,100;is=s");
        }
        radioMedium: Ieee80211ScalarRadioMedium {
            parameters:
                @display("p=100,200;is=s");
        }
        wirelessHost1: WirelessHost {
            parameters:
                @display("p=62,69");
        }
        wiredHost1: StandardHost {
            parameters:
                @display("p=296,134");
        }
        wiredHost2: StandardHost {
            parameters:
                @display("p=412,70");
        }
        router: Router {
            parameters:
                @display("p=296,69");
        }
        accessPoint: AccessPoint {
            parameters:
                @display("p=205,69");
        }
    connections:
        accessPoint.ethg++ <--> Eth100M <--> router.ethg++;
        wiredHost1.ethg++ <--> Eth100M <--> accessPoint.ethg++;
        wiredHost2.ethg++ <--> Eth100M <--> router.ethg++;
}
File: examples/wireless/wiredandwirelesshostswithap/WiredAndWirelessHostsWithAP.ned

This documentation is released under the Creative Commons license