Network

Package: inet.examples.pim.dm.assert

Network

network

(no description)

MulticastRouter MulticastRouter MulticastRouter StandardHost Ipv4NetworkConfigurator MulticastRouter StandardHost EthernetSwitch

Usage diagram

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Properties

Name Value Description
isNetwork

Unassigned submodule parameters

Name Type Default value Description
R1.status.initialStatus string "UP"

TODO @signal, @statistic
R1.pcapRecorder.verbose bool true

whether to log packets on the module output
R1.pcapRecorder.pcapFile string ""

the PCAP file to be written
R1.pcapRecorder.fileFormat string "pcapng"
R1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
R1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
R1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
R1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
R1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
R1.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
R1.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
R1.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
R1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
R1.pcapRecorder.displayStringTextFormat string "rec: %n pks"
R1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
R1.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R1.cb.forwardServiceRegistration bool true
R1.cb.forwardProtocolRegistration bool true
R1.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R1.bl.forwardServiceRegistration bool true
R1.bl.forwardProtocolRegistration bool true
R1.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R1.li.forwardServiceRegistration bool true
R1.li.forwardProtocolRegistration bool true
R1.eth.bitrate double
R1.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R1.nl.forwardServiceRegistration bool true
R1.nl.forwardProtocolRegistration bool true
R1.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R1.tn.forwardServiceRegistration bool true
R1.tn.forwardProtocolRegistration bool true
R1.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R1.at.forwardServiceRegistration bool true
R1.at.forwardProtocolRegistration bool true
R1.bgp.interfaceTableModule string

The path to the InterfaceTable module
R1.bgp.routingTableModule string
R1.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
R2.status.initialStatus string "UP"

TODO @signal, @statistic
R2.pcapRecorder.verbose bool true

whether to log packets on the module output
R2.pcapRecorder.pcapFile string ""

the PCAP file to be written
R2.pcapRecorder.fileFormat string "pcapng"
R2.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
R2.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
R2.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
R2.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
R2.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
R2.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
R2.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
R2.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
R2.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
R2.pcapRecorder.displayStringTextFormat string "rec: %n pks"
R2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
R2.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R2.cb.forwardServiceRegistration bool true
R2.cb.forwardProtocolRegistration bool true
R2.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R2.bl.forwardServiceRegistration bool true
R2.bl.forwardProtocolRegistration bool true
R2.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R2.li.forwardServiceRegistration bool true
R2.li.forwardProtocolRegistration bool true
R2.eth.bitrate double
R2.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R2.nl.forwardServiceRegistration bool true
R2.nl.forwardProtocolRegistration bool true
R2.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R2.tn.forwardServiceRegistration bool true
R2.tn.forwardProtocolRegistration bool true
R2.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R2.at.forwardServiceRegistration bool true
R2.at.forwardProtocolRegistration bool true
R2.bgp.interfaceTableModule string

The path to the InterfaceTable module
R2.bgp.routingTableModule string
R2.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
R3.status.initialStatus string "UP"

TODO @signal, @statistic
R3.pcapRecorder.verbose bool true

whether to log packets on the module output
R3.pcapRecorder.pcapFile string ""

the PCAP file to be written
R3.pcapRecorder.fileFormat string "pcapng"
R3.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
R3.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
R3.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
R3.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
R3.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
R3.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
R3.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
R3.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
R3.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
R3.pcapRecorder.displayStringTextFormat string "rec: %n pks"
R3.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
R3.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R3.cb.forwardServiceRegistration bool true
R3.cb.forwardProtocolRegistration bool true
R3.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R3.bl.forwardServiceRegistration bool true
R3.bl.forwardProtocolRegistration bool true
R3.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R3.li.forwardServiceRegistration bool true
R3.li.forwardProtocolRegistration bool true
R3.eth.bitrate double
R3.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R3.nl.forwardServiceRegistration bool true
R3.nl.forwardProtocolRegistration bool true
R3.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R3.tn.forwardServiceRegistration bool true
R3.tn.forwardProtocolRegistration bool true
R3.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R3.at.forwardServiceRegistration bool true
R3.at.forwardProtocolRegistration bool true
R3.bgp.interfaceTableModule string

The path to the InterfaceTable module
R3.bgp.routingTableModule string
R3.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
Source.status.initialStatus string "UP"

TODO @signal, @statistic
Source.pcapRecorder.verbose bool true

whether to log packets on the module output
Source.pcapRecorder.pcapFile string ""

the PCAP file to be written
Source.pcapRecorder.fileFormat string "pcapng"
Source.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
Source.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
Source.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
Source.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
Source.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
Source.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
Source.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
Source.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
Source.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
Source.pcapRecorder.displayStringTextFormat string "rec: %n pks"
Source.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
Source.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Source.cb.forwardServiceRegistration bool true
Source.cb.forwardProtocolRegistration bool true
Source.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Source.bl.forwardServiceRegistration bool true
Source.bl.forwardProtocolRegistration bool true
Source.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Source.li.forwardServiceRegistration bool true
Source.li.forwardProtocolRegistration bool true
Source.eth.bitrate double
Source.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Source.nl.forwardServiceRegistration bool true
Source.nl.forwardProtocolRegistration bool true
Source.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Source.tn.forwardServiceRegistration bool true
Source.tn.forwardProtocolRegistration bool true
Source.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Source.at.forwardServiceRegistration bool true
Source.at.forwardProtocolRegistration bool true
configurator.minLinkWeight double 1E-3
configurator.configureIsolatedNetworksSeparatly bool false
configurator.config xml xml("")

XML configuration parameters for IP address assignment and adding manual routes
configurator.assignAddresses bool true

assign IP addresses to all interfaces in the network
configurator.assignUniqueAddresses bool true

avoid using the same address and raise an error if not possible
configurator.assignDisjunctSubnetAddresses bool true

avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces
configurator.addStaticRoutes bool true

add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator.addDefaultRoutes bool true

add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator.addSubnetRoutes bool true

add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator.addDirectRoutes bool true

add direct routes (i.e. directly connected interfaces) to the routing table (used only if addStaticRoutes is true)
configurator.optimizeRoutes bool true

optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator.dumpTopology bool false

print extracted network topology to the module output
configurator.dumpLinks bool false

print recognized network links to the module output
configurator.dumpAddresses bool false

print assigned IP addresses for all interfaces to the module output
configurator.dumpRoutes bool false

print configured and optimized routing tables for all nodes to the module output
configurator.dumpConfig string ""

write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)
R4.status.initialStatus string "UP"

TODO @signal, @statistic
R4.pcapRecorder.verbose bool true

whether to log packets on the module output
R4.pcapRecorder.pcapFile string ""

the PCAP file to be written
R4.pcapRecorder.fileFormat string "pcapng"
R4.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
R4.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
R4.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
R4.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
R4.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
R4.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
R4.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
R4.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
R4.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
R4.pcapRecorder.displayStringTextFormat string "rec: %n pks"
R4.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
R4.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R4.cb.forwardServiceRegistration bool true
R4.cb.forwardProtocolRegistration bool true
R4.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R4.bl.forwardServiceRegistration bool true
R4.bl.forwardProtocolRegistration bool true
R4.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R4.li.forwardServiceRegistration bool true
R4.li.forwardProtocolRegistration bool true
R4.eth.bitrate double
R4.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R4.nl.forwardServiceRegistration bool true
R4.nl.forwardProtocolRegistration bool true
R4.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R4.tn.forwardServiceRegistration bool true
R4.tn.forwardProtocolRegistration bool true
R4.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
R4.at.forwardServiceRegistration bool true
R4.at.forwardProtocolRegistration bool true
R4.bgp.interfaceTableModule string

The path to the InterfaceTable module
R4.bgp.routingTableModule string
R4.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
Receiver.status.initialStatus string "UP"

TODO @signal, @statistic
Receiver.pcapRecorder.verbose bool true

whether to log packets on the module output
Receiver.pcapRecorder.pcapFile string ""

the PCAP file to be written
Receiver.pcapRecorder.fileFormat string "pcapng"
Receiver.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
Receiver.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
Receiver.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
Receiver.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
Receiver.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
Receiver.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
Receiver.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
Receiver.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
Receiver.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
Receiver.pcapRecorder.displayStringTextFormat string "rec: %n pks"
Receiver.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
Receiver.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Receiver.cb.forwardServiceRegistration bool true
Receiver.cb.forwardProtocolRegistration bool true
Receiver.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Receiver.bl.forwardServiceRegistration bool true
Receiver.bl.forwardProtocolRegistration bool true
Receiver.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Receiver.li.forwardServiceRegistration bool true
Receiver.li.forwardProtocolRegistration bool true
Receiver.eth.bitrate double
Receiver.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Receiver.nl.forwardServiceRegistration bool true
Receiver.nl.forwardProtocolRegistration bool true
Receiver.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Receiver.tn.forwardServiceRegistration bool true
Receiver.tn.forwardProtocolRegistration bool true
Receiver.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Receiver.at.forwardServiceRegistration bool true
Receiver.at.forwardProtocolRegistration bool true
switch.macTable.agingTime double
switch.macTable.forwardingTableFile string
switch.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
switch.l2NodeConfigurator.interfaceTableModule string
switch.l2NodeConfigurator.l2ConfiguratorModule string "l2NetworkConfigurator"

the absolute path to the ~L2NetworkConfigurator; use "" if there is no configurator
switch.status.initialStatus string "UP"

TODO @signal, @statistic
switch.pcapRecorder.verbose bool true

whether to log packets on the module output
switch.pcapRecorder.pcapFile string ""

the PCAP file to be written
switch.pcapRecorder.fileFormat string "pcapng"
switch.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
switch.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
switch.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
switch.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
switch.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
switch.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
switch.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
switch.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
switch.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
switch.pcapRecorder.displayStringTextFormat string "rec: %n pks"
switch.stp.helloTime double
switch.stp.forwardDelay double
switch.stp.maxAge double
switch.stp.bridgePriority int
switch.stp.visualize bool
switch.sc.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch.sc.forwardServiceRegistration bool true
switch.sc.forwardProtocolRegistration bool true
switch.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch.cb.forwardServiceRegistration bool true
switch.cb.forwardProtocolRegistration bool true
switch.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch.bl.forwardServiceRegistration bool true
switch.bl.forwardProtocolRegistration bool true
switch.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch.li.forwardServiceRegistration bool true
switch.li.forwardProtocolRegistration bool true
switch.cutthrough.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
switch.cutthrough.forwardServiceRegistration bool true
switch.cutthrough.forwardProtocolRegistration bool true
switch.eth.bitrate double

Source code

network Network
{
    submodules:
        R1: MulticastRouter {
            @display("p=400,200");
        }
        R2: MulticastRouter {
            @display("p=550,100");
        }
        R3: MulticastRouter {
            @display("p=550,300");
        }

        Source: StandardHost {
            @display("p=250,200");
        }
        configurator: Ipv4NetworkConfigurator {
            @display("p=100,100;is=s");
        }
        R4: MulticastRouter {
            @display("p=850,199");
        }
        Receiver: StandardHost {
            @display("p=1000,199");
        }
        switch: EthernetSwitch {
            @display("p=700,199");
        }
    connections allowunconnected:
        R1.ethg++ <--> Eth100M <--> R2.ethg++;
        R1.ethg++ <--> Eth100M <--> R3.ethg++;
        R1.ethg++ <--> Eth100M <--> Source.ethg++;

        switch.ethg++ <--> Eth100M <--> R2.ethg++;
        switch.ethg++ <--> Eth100M <--> R3.ethg++;
        R4.ethg++ <--> Eth100M <--> switch.ethg++;
        R4.ethg++ <--> Eth100M <--> Receiver.ethg++;
}
File: examples/pim/dm/assert/Network.ned

This documentation is released under the Creative Commons license