v3_4_routers_2_areas

Package: inet.examples.ospfv3.v3_4_routers_2_areas

v3_4_routers_2_areas

network

(no description)

Ipv4NetworkConfigurator Ospfv3Router Ospfv3Router Ospfv3Router Ospfv3Router Ospfv3Router

Usage diagram

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Properties

Name Value Description
isNetwork

Unassigned submodule parameters

Name Type Default value Description
configurator.minLinkWeight double 1E-3
configurator.configureIsolatedNetworksSeparatly bool false
configurator.assignAddresses bool true

assign IP addresses to all interfaces in the network
configurator.assignUniqueAddresses bool true

avoid using the same address and raise an error if not possible
configurator.assignDisjunctSubnetAddresses bool true

avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces
configurator.addStaticRoutes bool true

add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator.addDefaultRoutes bool true

add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator.addSubnetRoutes bool true

add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator.addDirectRoutes bool true

add direct routes (i.e. directly connected interfaces) to the routing table (used only if addStaticRoutes is true)
configurator.optimizeRoutes bool true

optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator.dumpTopology bool false

print extracted network topology to the module output
configurator.dumpLinks bool false

print recognized network links to the module output
configurator.dumpAddresses bool false

print assigned IP addresses for all interfaces to the module output
configurator.dumpRoutes bool false

print configured and optimized routing tables for all nodes to the module output
configurator.dumpConfig string ""

write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)
Router1.status.initialStatus string "UP"

TODO @signal, @statistic
Router1.pcapRecorder.verbose bool true

whether to log packets on the module output
Router1.pcapRecorder.pcapFile string ""

the PCAP file to be written
Router1.pcapRecorder.fileFormat string "pcapng"
Router1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
Router1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
Router1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
Router1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
Router1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
Router1.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
Router1.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
Router1.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
Router1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
Router1.pcapRecorder.displayStringTextFormat string "rec: %n pks"
Router1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
Router1.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router1.cb.forwardServiceRegistration bool true
Router1.cb.forwardProtocolRegistration bool true
Router1.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router1.bl.forwardServiceRegistration bool true
Router1.bl.forwardProtocolRegistration bool true
Router1.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router1.li.forwardServiceRegistration bool true
Router1.li.forwardProtocolRegistration bool true
Router1.eth.bitrate double
Router1.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router1.nl.forwardServiceRegistration bool true
Router1.nl.forwardProtocolRegistration bool true
Router1.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router1.tn.forwardServiceRegistration bool true
Router1.tn.forwardProtocolRegistration bool true
Router1.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router1.at.forwardServiceRegistration bool true
Router1.at.forwardProtocolRegistration bool true
Router1.bgp.interfaceTableModule string

The path to the InterfaceTable module
Router1.bgp.routingTableModule string
Router1.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
Router2.status.initialStatus string "UP"

TODO @signal, @statistic
Router2.pcapRecorder.verbose bool true

whether to log packets on the module output
Router2.pcapRecorder.pcapFile string ""

the PCAP file to be written
Router2.pcapRecorder.fileFormat string "pcapng"
Router2.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
Router2.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
Router2.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
Router2.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
Router2.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
Router2.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
Router2.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
Router2.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
Router2.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
Router2.pcapRecorder.displayStringTextFormat string "rec: %n pks"
Router2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
Router2.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router2.cb.forwardServiceRegistration bool true
Router2.cb.forwardProtocolRegistration bool true
Router2.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router2.bl.forwardServiceRegistration bool true
Router2.bl.forwardProtocolRegistration bool true
Router2.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router2.li.forwardServiceRegistration bool true
Router2.li.forwardProtocolRegistration bool true
Router2.eth.bitrate double
Router2.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router2.nl.forwardServiceRegistration bool true
Router2.nl.forwardProtocolRegistration bool true
Router2.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router2.tn.forwardServiceRegistration bool true
Router2.tn.forwardProtocolRegistration bool true
Router2.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router2.at.forwardServiceRegistration bool true
Router2.at.forwardProtocolRegistration bool true
Router2.bgp.interfaceTableModule string

The path to the InterfaceTable module
Router2.bgp.routingTableModule string
Router2.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
Router3.status.initialStatus string "UP"

TODO @signal, @statistic
Router3.pcapRecorder.verbose bool true

whether to log packets on the module output
Router3.pcapRecorder.pcapFile string ""

the PCAP file to be written
Router3.pcapRecorder.fileFormat string "pcapng"
Router3.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
Router3.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
Router3.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
Router3.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
Router3.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
Router3.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
Router3.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
Router3.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
Router3.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
Router3.pcapRecorder.displayStringTextFormat string "rec: %n pks"
Router3.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
Router3.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router3.cb.forwardServiceRegistration bool true
Router3.cb.forwardProtocolRegistration bool true
Router3.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router3.bl.forwardServiceRegistration bool true
Router3.bl.forwardProtocolRegistration bool true
Router3.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router3.li.forwardServiceRegistration bool true
Router3.li.forwardProtocolRegistration bool true
Router3.eth.bitrate double
Router3.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router3.nl.forwardServiceRegistration bool true
Router3.nl.forwardProtocolRegistration bool true
Router3.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router3.tn.forwardServiceRegistration bool true
Router3.tn.forwardProtocolRegistration bool true
Router3.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router3.at.forwardServiceRegistration bool true
Router3.at.forwardProtocolRegistration bool true
Router3.bgp.interfaceTableModule string

The path to the InterfaceTable module
Router3.bgp.routingTableModule string
Router3.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
Router4.status.initialStatus string "UP"

TODO @signal, @statistic
Router4.pcapRecorder.verbose bool true

whether to log packets on the module output
Router4.pcapRecorder.pcapFile string ""

the PCAP file to be written
Router4.pcapRecorder.fileFormat string "pcapng"
Router4.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
Router4.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
Router4.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
Router4.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
Router4.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
Router4.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
Router4.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
Router4.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
Router4.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
Router4.pcapRecorder.displayStringTextFormat string "rec: %n pks"
Router4.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
Router4.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router4.cb.forwardServiceRegistration bool true
Router4.cb.forwardProtocolRegistration bool true
Router4.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router4.bl.forwardServiceRegistration bool true
Router4.bl.forwardProtocolRegistration bool true
Router4.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router4.li.forwardServiceRegistration bool true
Router4.li.forwardProtocolRegistration bool true
Router4.eth.bitrate double
Router4.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router4.nl.forwardServiceRegistration bool true
Router4.nl.forwardProtocolRegistration bool true
Router4.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router4.tn.forwardServiceRegistration bool true
Router4.tn.forwardProtocolRegistration bool true
Router4.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router4.at.forwardServiceRegistration bool true
Router4.at.forwardProtocolRegistration bool true
Router4.bgp.interfaceTableModule string

The path to the InterfaceTable module
Router4.bgp.routingTableModule string
Router4.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""
Router5.status.initialStatus string "UP"

TODO @signal, @statistic
Router5.pcapRecorder.verbose bool true

whether to log packets on the module output
Router5.pcapRecorder.pcapFile string ""

the PCAP file to be written
Router5.pcapRecorder.fileFormat string "pcapng"
Router5.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
Router5.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
Router5.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*]"

space-separated list of sibling module names to listen on
Router5.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
Router5.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
Router5.pcapRecorder.dumpProtocols string "ethernetmac ppp ieee80211mac"

space-separated list of protocol names as defined in the Protocol class
Router5.pcapRecorder.packetFilter object "*"

which packets are considered, matches all packets by default
Router5.pcapRecorder.helpers string ""

usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
Router5.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
Router5.pcapRecorder.displayStringTextFormat string "rec: %n pks"
Router5.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
Router5.cb.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router5.cb.forwardServiceRegistration bool true
Router5.cb.forwardProtocolRegistration bool true
Router5.bl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router5.bl.forwardServiceRegistration bool true
Router5.bl.forwardProtocolRegistration bool true
Router5.li.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router5.li.forwardServiceRegistration bool true
Router5.li.forwardProtocolRegistration bool true
Router5.eth.bitrate double
Router5.nl.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router5.nl.forwardServiceRegistration bool true
Router5.nl.forwardProtocolRegistration bool true
Router5.tn.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router5.tn.forwardServiceRegistration bool true
Router5.tn.forwardProtocolRegistration bool true
Router5.at.displayStringTextFormat string "processed %p pk (%l)"

determines the text that is written on top of the submodule
Router5.at.forwardServiceRegistration bool true
Router5.at.forwardProtocolRegistration bool true
Router5.bgp.interfaceTableModule string

The path to the InterfaceTable module
Router5.bgp.routingTableModule string
Router5.bgp.ospfRoutingModule string parent.hasOspf ? "^.ospf" : ""

Source code

network v3_4_routers_2_areas
{
    types:
        channel Channel extends ThruputMeteringChannel
        {
            delay = 0.1us;
            datarate = 100Mbps;
            thruputDisplayFormat = "#N";
        }
    submodules:
        configurator: Ipv4NetworkConfigurator {
            parameters:
                config = xml("<config>"+
                            "<interface among='Router1 Router2' address='10.10.10.x' netmask='255.255.255.0' />"+
                            "<interface among='Router2 Router3' address='10.10.20.x' netmask='255.255.255.0' />"+
                            "<interface among='Router3 Router4' address='10.10.30.x' netmask='255.255.255.0' />"+
                            "<interface among='Router3 Router5' address='10.10.40.x' netmask='255.255.255.0' />"+
                            "</config>");
                @display("p=147,54");
        }
        Router1: Ospfv3Router {
            parameters:
                @display("p=56,230");
            gates:
                ethg[1];
        }
        Router2: Ospfv3Router {
            parameters:
                @display("p=213,153");
            gates:
                ethg[2];
        }
        Router3: Ospfv3Router {
            parameters:
                @display("p=376,153");
            gates:
                ethg[3];
        }
        Router4: Ospfv3Router {
            parameters:
                @display("p=519,50");
            gates:
                ethg[1];
        }
        Router5: Ospfv3Router {
            parameters:
                @display("p=508,212");
            gates:
                ethg[1];
        }
    connections:
        Router1.ethg[0] <--> Channel <--> Router2.ethg[0];
        Router2.ethg[1] <--> Channel <--> Router3.ethg[0];
        Router3.ethg[1] <--> Channel <--> Router4.ethg[0];
        Router3.ethg[2] <--> Channel <--> Router5.ethg[0];
}
File: examples/ospfv3/v3_4_routers_2_areas/v3_4_routers.ned

This documentation is released under the Creative Commons license